Supported Models

Version 2.3.4

Downloads

Release Notes

Version 2.3.2

Downloads

Release Notes

Version 2.3.1

Downloads

---

Version 2.3.0

Downloads

Release Notes

• New Feature: Added 12 client support for 60GHz radio
  
• New Feature: Added MCS12 support for 60GHz radio
  
• New Feature: Added STP control
  
• New Feature: Added Jumbo frame support for 5GHz radio (up to 7912)
  
• New Feature: Added support for RSTP passthrough
  
• New Feature: Added L2 and L3 MTU control options
  
• Improved: RSSI (signal level) representation for 60GHz
  
• Improved: multicast parameters
  
• Improved: traffic shaping ruleset
  
• Improved: UI (added L2, L3 mtu to dashboard)
  
• Improved: failover mechanism with high system load
  
• Improved: performance with VLAN functions
  
• Improved: decreased stats interval
  
• Fixed: TIPC random memory corruption
  
• Fixed: minor UI bugs related to display
  
• Fixed: 5GHz radio crash when multicast traffic is being sent
  
• Fixed: L2 isolation on LW platform
  
• Fixed: aiming mode issues
  
• Fixed: RCU stalls
  
• Fixed: station disconnects and can't reconnect
  
• Fixed: Ethernet port goes up/down
  
• Fixed: Ethernet port stalls if there is too much packet loss
  
• Fixed: mDNS (GUI issues)
  
• Fixed: interfaces not being added to bridge
  
• Fixed: 60 GHz radio scan problem
  
• Fixed: IGMP snooping
  
• Fixed: missing stations list stats gathering
  
• Fixed: SSID validation issue
  
• Fixed: config restoration when management vlan is used
  

Version 2.2.1

Downloads

Release Notes

• Improved: traffic shaping rules
  
• Improved: radio recovery utility
  
• Improved: LW product performance
  
• Fixed: mtu reconfiguration on LW products
  
• Known Issue: Omni performance is impacted by bad clients with low signal levels
  
• Known Issue: Occasional 5GHz disconnects are observed during long term testing
  

Version 2.2.0

Downloads

Release Notes

• New Feature: Added new management vlan control options
  
• New Feature: built-in discovery option
  
• New Feature: Added beamwidth control option with possibility to select between 10, 30, 60, 90, 120 beamwidth
  
• New Feature: Added channel list selection option
  
• New Feature: Added station mode with backup for ML-60-10G-360
  
• New Feature: Added Metrolinq Peer List
  
• New Feature: 5G station and ap backup modes
  
• New Feature: mactelnet support
  
• New Feature: Added remote peer stats
  
• Improved: Improved UI and it’s usage
  
• Improved: recovered RPS for ML2.5
  
• Improved: Refactored usbwatchd utility
  
• Improved: Peer bonding utility
  
• Fixed: Traffic control for tagged traffic
  
• Fixed: Increased performance for tagged traffic.
  
• Fixed: CPU utilization stats
  
• Fixed: Ethernet and SFP control for ML-60-LW
  
• Fixed: Jumbo frame passthrough over ML-60-LW
  
• Fixed: Network reconfiguration hang issue
  
• Fixed: Site survey functionality for 60G radio
  
• Fixed: EAPOL frames handling for ML-60-LW, ML-5-LW
  
• Fixed: Missing macaddr migration for ML-5-LW
  
• Known Issue: Aiming mode does not show accurate remote signal level
  
• Known Issue: ML2.5-BF-18 and ML-60-LW reports lower signal level for 60G radio
  
• Known Issue: PTMP 60G performance is low with bad 60G clients connected
  

Version 2.1.1

Downloads:

Release Notes:

• Improved latency on 60 GHz
  
• Fixed 60 GHz radio configuration issue
  
• Disabled fwlogs by default
  
• Updated Japan country regdb rules
  

Version 2.1.0

Downloads:

Release Notes:

• Fixed: LACP, LLDP not working
  
• Fixed: Buffer memory issue on 60 GHz
  
• Fixed: UMAC timeout on 60 GHz
  
• Improvement: DFS patterns and operation logic improvements
  
• Improvement: Q-in-Q passthrough improvements
  
• Improvement: Noise floor stats added into statistics
  
• Improvement: 60GHz queue mechanism optimization (allows to reach higher max throughput)
  
• Improvement: Improved speedtest utility
  
• New Feature: Added traffic control
  
• New Feature: Added 60 GHz scan function
  

---

Version 2.0.4

Downloads

Release Notes

• Added initial Cloud support and fixed some stats reporting issues.
  

Downloads

Release Notes

• Fixed: DSCP priority would drop certain packets on 60GHz radio 
  
• Fixed: Wan mac value not restored when using config backup
  
• Fixed: Kernel panic in some scenarios when high pps is being sent
  
• Fixed: 60GHz clients stats display on UI 
  
• Fixed: 5GHz disconnects in some scenarios
  
• Fixed: Link uptime statistics gathering for 5GHz 
  
• Fixed: iw tool now can set properly allowed bands for 60GHz
  
• Fixed: 60GHz radio RSN would cause stations disconnect in PTMP 
  
• Fixed: Inaccurate traffic graph display on UI
  
• Fixed: Discovery utility would not show device name 
  
• Improvement: Add linkid info for troubleshooting file
  
• Improvement: Added new scan functionality for 60G and updated 5GHz
  
• Improvement: Updated 5GHz DFS patterns and operational logic
  
• Improvement: 60GHz queue mechanism optimization (allows to reach higher max throughput)
  
• Improvement: Updated regdb database (Malaysia, NZ, AU country code)
  
• Improvement: Peerbonding configuration utility
  
• Improvement: snmpd stats gathering
  
• Improvement: Updated test/apply/revert functionality
  
• Improvement: Updated DCS for 5GHz radio
  
• Improvement: Increased default network backlog queue size (resolves packet drop)
  
• Improvement: Increased UI Speed
  
• Improvement: Updated stats gathering for 60GHz and 5GHz radios
  
• New Feature: Added Speedtest utility for link capacity measurements
  
• New Feature: Added data vlan for 5GHz radio 
  
• New Feature: Added separate load balancing for 60GHz radio