MetroLinq 5 LW Firmware

MetroLinq 5 LW Firmware

Supported Models

The firmware on this page applies to the following MetroLinq models:
 
ML-60-5-LW-XX


Version 2.3.5

June 27, 2019

Downloads

Release Notes

  1. NOTE: Upgrade client units first
  2. Fixed an issue where a wireless link isn't possible between ML1 and other ML units when the ML1 is used as the Master.


Version 2.3.0

January 31, 2019

Downloads

Release Notes


Version 2.2.1-Beta

November 1, 2018

Downloads

Release Notes

  • Improved: traffic shaping rules
  • Improved: radio recovery utility
  • Improved: LW product performance
  • Fixed: mtu reconfiguration on LW products
  • Known Issue: Omni performance is impacted by bad clients with low signal levels
  • Known Issue: Occasional 5GHz disconnects are observed during long term testing


Version 2.2.0

August 28, 2018

Downloads

Release Notes

  • New Feature: Added new management vlan control options
  • New Feature: built-in discovery option
  • New Feature: Added channel list selection option
  • New Feature: Added Metrolinq Peer List
  • New Feature: mactelnet support
  • New Feature: Added remote peer stats
  • Improved: Improved UI and it’s usage
  • Fixed: Traffic control for tagged traffic
  • Fixed: Increased performance for tagged traffic.
  • Fixed: CPU utilization stats
  • Fixed: Network reconfiguration hang issue
  • Fixed: EAPOL frames handling for ML-5-LW
  • Fixed: Missing macaddr migration for ML-5-LW



Version 2.1.1

August 3, 2018

Downloads

Release Notes

  • Fixed "disable reset" setting
  • Improved memory handling
  • Disabled fwlogs by default
  • Updated Japan country regdb rules



Version 2.1.0

May 29, 2018

Downloads:

Release Notes:

  • Improvement: DFS patterns and operation logic improvements
  • Improvement: Q-in-Q passthrough improvements
  • Improvement: Noise floor stats added into statistics
  • Improvement: Improved speedtest utility
  • New Feature: Added traffic control



    • Related Articles

    • MetroLinq 60 One (ML1) & MetroLinq 60 LW (ML-60-LW) Firmware

      Supported Models The firmware on this page applies to the following MetroLinq models:   ML-60-LW-XX ML1-60-XX Version 2.4.2 May 11, 2020 Downloads ML 60 LW -2.4.2-4531 ML 60 One - 2.4.2-4531 Release Notes Fix 2.4Ghz can not be disabled issue Fix TX ...
    • MetroLinq 2.5G 60 Firmware

      Supported Models The firmware on this page applies to the following MetroLinq models:   ML2.5-60-35-XX ML2.5-60-19-XX ML2.5-60-BF-18-XX  Upgrade Alerts Please read the following message carefully before upgrading! Devices running firmware versions ...
    • MetroLinq 10G Omni Firmware

      Supported Models The firmware on this page applies to the following MetroLinq models:  ML-60-10G-360-XX Version 2.4.2 May 11, 2020 Downloads 2.4.2-4179 Release Notes NOTE: Upgrade client units first Fix 2.4Ghz can not be disabled issue Fix TX power ...
    • MetroLinq 60 (ML-60 first generation) Firmware

      Supported Models The firmware on this page applies to the following MetroLinq models ONLY: ML-60-35 ML-60-19 ML-60-30-18 Must-Read Upgrade Notes: 1.1.8 and later FW versions are not compatible with MetroLinq serial serial numbers starting with AF ...
    • ML-60-LW info and links

      Introduction IgniteNet’s MetroLinq 60 LW (lightweight) changes the economics of low-cost 60GHz PTP and PTMP connections. With a 60GHz range of up to 150m (0.1mi) as well as built-in 5GHz failover, it can provide reliable high throughput in the ...
      Didn't find what you were looking for?
    Or
    Email Us: support@ignitenet.com
    (Please remember to submit TS file)
    (Please note, by clicking 'Create Support Ticket' you will be redirected  to our new Edgecore System Portal, please register your ticket via our Edgecore System as IgniteNet is now part of Edgecore.)